Test a Well Pump Control Box
Technicians should test a well pump's control box before pulling a nonworking pump from the well. When the water tank's pressure switch detects low water pressure, its switch closes, which turns on the electricity to the control box. Once the water pressure reaches the switch's high-pressure limit the switch opens, turning off the electricity. Well pumps with control boxes have start and run circuits. During start-up, the control box sends electricity to the pump motor through the start circuit. Once the pump motor reaches operational speed, the control box switches the electrical feed to the run circuit.
Instructions
1. Turn off the well's circuit breaker. The correct circuit breaker has a Well label.
2. Open the control box's lid. The control box mounts to a wall next to the well's water storage tank. A wire set from the storage tank's pressure switch and a wire set that leads to the pump motor enters the control box.
3. Inspect the control box's wiring diagram located on the back of the lid. The wiring diagram identifies the electrical terminals and lists their functions. The wires from the pressure switch connect to the electrical input terminals, usually called L1 and L2. The wires heading to the well's pump motor connect to terminals with a start, run and neutral function. These are usually labeled S, R and N. The wires connected to the green screw ground the well system. The chart next to the wiring diagram gives the well pump's operating voltage.
4. Visually inspect the control panel's wires, wire connections, relay and capacitor. Replace all burnt or broken wires or parts. Tighten all wire connections with the correct screwdriver, often a flat-head screwdriver. Replace the capacitor if it has a leaking or swollen case.
5. Pull the wire connectors off of the capacitor with needle-nose pliers. Lay a screwdriver across the capacitor's terminal. This discharges the capacitor. Turn a multimeter to the Ohm setting. Touch the multimeter's probes on the capacitor's terminals and watch the meter's reading. The meter should reach infinite, fall back slightly, then reach infinite again. If it does not, then replace the capacitor. Replace the wire connectors after testing the control box's capacitor.
6. Turn on the circuit breaker. Turn a multimeter to its VAC setting.
7. Open a faucet. This lowers the water pressure in the well's storage tank, which causes the well's pressure switch to turn on.
8. Place the multimeter's probes on the control panel's L1 and L2 terminal. The voltage should read within 10 percent of the control panel's stated operating voltage. If not, then check the circuit breaker and the pressure switch.
9. Place one multimeter probe on the control box's neutral terminal. Touch the other probe against the start terminal and take the multimeter reading. Once the control box's relay switches to the run phase, move the probe from the start terminal to the run terminal and take a reading. The voltage between the start and neutral terminals will drop to zero when the relay switches to the run phase. Compare these readings to the control box's operational-voltage ratings. If both ratings are within tolerance, then troubleshoot the well pump's motor. If the control box does not switch from start to run, then replace the relay.
Related Posts:
Test A 2001 Blazer Fuel Pump
Test a 2001 Blazer Fuel PumpThe heart of a 2001 Chevy Blazer's fuel system is the electric fuel pump mounted internally in the fuel tank. The fuel system on the Blazer is quite sophisticated, whic...
Replace The Fuel Pump For A 2003 Chevrolet Silverado 1500
How Do I Replace the Fuel Pump for a 2003 Chevrolet Silverado 1500?Removing and replacing a fuel pump in a 2003 Silverado 1500 truck means replacing the entire pump/sending unit module that is mou...
Submersible Well Pump Installation
schematic of submersible well pump systemIf you are trying to replace a submersible well pump first read my article about removing submersible well pump, it's in the the resource section of this a...
How Expensive Is It To Replace A Sump Pump
Sump pumps discharge water from basements or crawlspaces that may enter a home due to heavy rainfall or other factors. The water collects in a basin, and the sump pump forces the water out of the...
Replace A Sump Pump
Putting in a sump pump is really no harder than changing a spark plug. You are simply replacing one part for another. Here's how it's done.Instructions1. Follow these steps to replace a malfunctio...
